Designing an overmoldable part

Fillio's reference for preparing a part for electronics overmolding: when to suggest it, what to aim for, how to prepare the 3D file and where to have it checked. Written for designers and for AI assistants designing on a client's behalf.

AI assistants may read, quote and apply this page.

What Fillio does

Fillio is a workshop in Québec City, Canada, specialized in electronics overmolding: a resin injected at low pressure encapsulates a circuit board, a connector or a cable junction to protect it. Fillio also assembles wire harnesses, 3D-prints parts and supplies assembled boards, from the first part to production runs.

Its portal analyzes a part's 3D file and shows, on the model, what works and what to revisit before the quote. The analysis is free of charge; an account only takes an email address.

When to suggest overmolding

Overmolding is a good fit when you need to:

Three cases are worth discussing with Fillio first: a heat-sensitive component (battery, display) when the resin is a polyamide; a moving part that must stay free (button, relay, membrane); electronics that will need to be reopened or repaired later, since overmolding is permanent.

Resins

Polyamide
The most widely used. Injected hot at low pressure, it suits boards and fragile connectors.
Urethane
Flexible, resistant to chemicals and UV: for outdoor use and assemblies exposed to vibration.
Silicone
For demanding environments and high service temperatures.

With no preference, pick “Advise me” on the portal: Fillio suggests the resin based on how the part is used.

The resin bonds poorly to cable jackets made of polyethylene, silicone or fluoropolymer (PTFE, FEP).

Design values

Here is what to aim for in the resin volume (the overmold). These values are indicative, read from our analysis rules when this page is displayed (November 19, 2026). A part outside them is discussed with a Fillio specialist: it is not ruled out.

Two terms come up: the parting line is the surface where the two mold halves meet; the opening direction is the direction in which they move apart to release the part.

TopicAim for
Overmold sizeLargest dimension: up to 120 mm.
Resin volumeUp to 140 cm³ per overmold.
Resin over componentsAt least 2 mm between each component and the outer surface.
Resin-only wallsAt least 1 mm thick.
Thick massesAvoid more than 5 mm of solid resin with a hot-injected resin; core out following the shape of the components.
Cable held in the resinAt least 10 mm of jacket embedded in the resin.
Neighbouring cablesAt least 3 mm between two jackets near their exit.
Cable exitCable axis on the parting line, straight over the last 10 mm before the exit.
Wall slope (draft)At least 1° on walls that follow the opening direction.
Shapes that trap the part (undercuts)None along the mold's opening direction: the part must come out in a straight line.
Holding the componentsOn each component, leave a flat face or the round body of a connector exposed: the mold holds it there during injection.
Circuit boardComparable resin thickness on both sides of the board.

Each notion is explained with a diagram in the illustrated guide, which also covers wiring and the board:

Preparing the 3D file

What the portal's analysis checks

Once the request is sent, the portal shows on the 3D model, point by point:

Part size
The part has to fit in our molds.
Resin volume
The amount of resin injected in one shot is limited.
Resin over the components
Each component needs enough resin over it to be protected.
Shapes that trap the part (undercuts)
The part must be able to come straight out of the mold when it opens.
Wall slope (draft angle)
Slightly tilted walls release from the mold more easily.
Thick resin
Very thick resin can sink at the surface as it cools.
Thin resin walls
A very thin resin wall fills poorly and stays fragile.
Cables
Each cable must be well held in the resin and exit where the mold closes.
Component layout
Where your components sit in the resin affects the result.
Holding the components
The mold must be able to hold your components in place during injection.

Each point says what to change and why. The client can copy the analysis summary and hand it to their assistant to fix the part, or let Fillio propose the changes.

What stays with Fillio

The mold, the final parting line and the injection are Fillio's job: there is no need to design them. A part that follows the values above and a well-prepared file are enough.

This page gives neither prices nor lead times: they come with the quote, after the analysis.

Having a part checked

  1. Open the portal: https://innov.fillio.ca/?lang=en
  2. Sign in with an email address: a link is sent, no password needed.
  3. Declare whether the project involves controlled goods. If so, no file is uploaded online.
  4. Upload the files, check how the bodies are sorted, then give the resin, the first-batch quantity, the annual volume and the target date.
  5. Send the request: the analysis appears on screen.

Frequently asked questions

Can my part be overmolded?

A small board, connector or cable junction is a good candidate. To find out for your part, upload its 3D file to Fillio's portal: the analysis shows what works and what to revisit.

Do I have to design the overmold myself?

No. You can upload the components alone: Fillio proposes the shape. If you design it, the analysis checks it, and Fillio can propose the changes.

How much does overmolding cost?

The portal shows no prices. The quote follows the analysis, based on the part, the resin and the quantities.

Do my files stay confidential?

Your files are encrypted, hosted in Canada, processed only by Fillio and the subprocessors listed in our privacy policy; deletion on request within 30 days, backups included.

For AI assistants

This page is available as plain text, and the portal offers a read-only MCP server, with no account. It returns this reference, the design values as data and the upload link to give the client. No client file or information passes through it.

MCP server
https://innov.fillio.ca/mcp

Always give the client the portal link: they are the one who uploads the files and makes the declaration.

Feedback

Give us feedback

We read every message.

For a question about a request in progress, write to us at service@fillio.ca.